Unit of Measure


N/A 460 V


N/A 60 Hz

Number of Phases

N/A 3

Total Capacity

N/A 86000 Btu/hr

Net Sensible Capacity

N/A 67400 Btu/hr

Net Latent Capacity

N/A 18600 Btu/hr


N/A 11

Sound Rating

N/A 82 dB

Indoor CFM

N/A 3000 ft³/min

Heating Capacity - Outdoor Air 47ºF DB/43ºF WB

N/A 90000 Btu/hr

COP - Outdoor Air 47ºF DB/43ºF WB

N/A 3.3

Heating Capacity - Outdoor Air 17ºF DB/15ºF WB

N/A 55000 Btu/hr

COP - Outdoor Air 17ºF DB/15ºF WB

N/A 2.2

Compressor Type

N/A Z-Scroll

Compressor - Rated Load Amperes (RLA)

N/A 12.8 A

Compressor - Locked Rotor Amperes (LRA)

N/A 100 A

Fan Motor - Full Load Amperes

N/A 2.3 A

Minimum Circuit Ampacity

N/A 19 A

Fuse or HACR Circuit Breaker - Minimum

N/A 25 A

Fuse or HACR Circuit Breaker - Maximum

N/A 30 A

Outdoor Coil - Face Area

N/A 34.50 ft²

Outdoor Coil - No. Rows

N/A 2

Outdoor Coil - CFM

N/A 5000 ft³/min

Refrigeration Per Circuit

N/A 10546 g372 oz


N/A 448 lb


N/A 31 1/8 in


N/A 42 11/16 in


N/A 48 13/16 in


  • CABINET—Galvanized steel with powder coat paint finish. The powder coat paint finish is high gloss, durable and capable of withstanding a 1000-hour salt spray test per ASTM B 117. All access panels can be opened or removed without affecting the structural strength of the unit. Stamped louvered panels offer 100% protection for the condenser coil.
  • EQUIPMENT GROUND— Lug for field connection of ground wire.
  • CONTACTOR—The contactor is an electrical switch which operates the compressor and outdoor fans. Its 24 volt coil is activated on a call for cooling or heating.
  • TRANSFORMER—75 VA step-down type, from Line to 24 volts with resetable circuit breaker.
  • CAPACITOR—Help provide starting torque necessary to boost the condenser fan motors to operating speed by directing their stored energy to the starter winding in step with the running winding.
  • DEMAND DEFROST CONTROL—Used when unit is in heating mode to defrost outdoor coil.
  • AUTO-RESET HIGH PRESSURE CONTROL, AND AUTORESET LOW PRESSURE CONTROL—To provide compressor protection under abnormally high head pressure conditions (outdoor fan failure, restriction, dirty coil, etc.) or abnormally low suction pressure conditions (restrictions, TEV failure, loss of charge, indoor blower failure, etc.) while eliminating nuisance tripping sometimes experienced with conventional control systems.
  • COIL—Constructed with copper tubes and aluminum fins mechanically bonded to tubes for maximum heat transfer capabilities. All coil assemblies are leak tested up to 550 PSIG (3792 kPa) internal pressure.
  • SERVICE ACCESS—Control box with separate line and control voltages, as well as compressor and other refrigerant controls are accessible through access panels. An electrical access cover may be opened or removed without affecting normal operation of the unit. Condenser fan motors are equipped with molded plugs for easy removal. Louver panels and end access panel can be removed for coil cleaning.
  • BASE PAN—Galvanized steel with powder coat paint finish.
  • COMPRESSOR—The Scroll Compressor is hermetically sealed with internal high temperature protection, and durable insulation on motor windings. The entire compressor is mounted on rubber grommets to reduce vibration and noise.
  • TX VALVE—Used when unit is in heating mode and outdoor coil functions as evaporator.
  • CRANKCASE HEATER—Minimizes refrigerant migration to compressor sump.
  • SUCTION LINE ACCUMULATOR—To prevent liquid slugging of compressor.
  • REFRIGERANT CONNECTIONS—All field sweat joints are made external of the unit and are located close to the ground for a neat looking installation.
  • SERVICE VALVES—Standard on liquid line and vapor line.
  • REVERSING VALVE—Sized for maximum capacity and efficiency, 24V coil, energized in heating.